江门恩平快速维修伦茨E70ACPSE0604S伺服驱动器过流故障
![](http://static.11467.com/img/ab-prev-0.png)
![](http://img2.11467.com/2023/07-19/3935985309_small.jpg)
![](http://img2.11467.com/2023/07-19/3935985309_small.jpg)
![](http://img2.11467.com/2023/07-19/3934770000_small.jpg)
![](http://img.11467.com/2023/05-27/1828692598_small.jpg)
![](http://img.11467.com/2023/07-20/1017683484_small.jpg)
![](http://img.11467.com/2023/06-07/957886426_small.jpg)
![](http://static.11467.com/img/ab-next-0.png)
江门恩平快速维修伦茨E70ACPSE0604S伺服驱动器过流故障
江门伦茨i700伺服驱动器维修常见故障,结合个人维修经验,主要有以下:
1.上电无显示(红灯、蓝灯均不亮)
2.上电报警(红灯常亮),常见报警代码如下:
维修LENZE伦茨i700伺服驱动器各种故障:
恩平伦茨伺服驱动器维修,江门伦茨伺服控制器维修,新会伦茨伺服放大器维修常见故障修复:炸机,模块炸,带不动负载,主轴准备未绪,无使能,使能不上,驱动器未使能,编码器报警故障,主轴驱动模块报警,输出电压低,红色灯亮,无显示,缺相,输出控制点坏,使能不正常,报故障,不能启动、过流、过压、欠压、过热、过载、输出不平衡、无显示、开关电源损坏、模块损坏、接地故障、不能调速、限流运行,Z轴报警,X轴无法使能,台山Y轴短期内驱动故障维修,驱动电机变频器出错,轴伺服故障,伺服电机不转。
0x2320 Short circuit or earth leakage at the motor end
Heatsink: Fan is defect 119 [0x00770010] 16 散热器:风扇故障 故障
Inside the device: Fan is defective 119 [0x00770011] 17 设备内部:风扇故障 故障
120(模拟信号监测)
Device utilisation Ixt > C00123 120 [0x00780000] 0 过电流> C00123的频繁且过长的加速过程 无
Device utilisation Ixt > 100 % 120 [0x00780001 1 频繁且过长的加速过流过程 故障
Motor load I2xt > C00127 120 [0x00780002] 2 电机负载I2xt> C00127 故障
Motor load I2xt > C00120 120 [0x00780003] 3 电机负载I2xt> C00120 故障
Control card is defect (UB24) 120 [0x00780004] 4 控制卡有问题(UB24) 系统故障
Control card is defect (VCC15) 120 [0x00780005] 5 控制卡有问题(VCC15正) 系统故障
Control card is defect (UB80) 120 [0x00780006] 6 控制卡有问题(UB8) 系统故障
Control card is defect (VCC15 neg.) 120 [0x00780007] 7 控制卡有问题(VCC15负) 系统故障
Control card is defect (UB18 neg.) 120 [0x00780008] 8 控制卡有问题(UB18负) 系统故障
Control card is defect (VCC5) 120 [0x00780009] 9 控制卡有问题(VCC5) 系统故障
Electronic nameplate: Dataare incompatible 120 [0x0078000a] 10 电子铭牌:数据不兼容控制器固件不支持带反馈的连接电机。 信息
121(电机数据接口)
Device command transferred incorrectly 121 [0x00790000] 0 设备命令传输错误(电机数据接口) 系统故障
Time error - controller interface 121 [0x00790001] 1 时间错误 - 控制器接口(电机数据接口) 系统故障
Violation of time slice 121 [0x00790002] 2 电机数据接口违反同步时间 系统故障
123(电机控制)